FEBRUARY ONLINE AUCTION

Farm Land and Equipment in Grand Forks, North Dakota, United States

26 Friday
26th February, 2021 12:00 PM

FEBRUARY ONLINE AUCTION

Farm Land and Equipment in Grand Forks North Dakota, United States

Friday at - 26th February , 2021

Close

Description

FEBRUARY ONLINE AUCTION
 
BIDS OPEN FEBRUARY 22nd; CLOSE FEBRUARY 26th
 
CLICK HERE FOR ONLINE CATALOG AND BIDDING
 
CLICK ABOVE FOR ONLINE CATALOG INCLUDING EQUIPMENT DESCRIPTIONS, SALE ORDER, BIDDING PROCEDURE, INSPECTION & LOAD OUT LOCATIONS AND ADDITIONAL PHOTOS
 
LOW RATE FINANCING IS AVAILABLE ON MAJOR UNITS, INTEREST WAIVER ON COMBINES. CONTACT MARK AT 701-757-4015 FOR DETAILS…..MUST BE PRE-APPROVED BY FEBRUARY 24th. 
 
TRACTORS:
 
2015 New Holland T8.350 MFWD, Auto Command trans, luxury cab, guidance ready w/ Trimble 1000 display, RTK capable, receiver & Nav II controller, front HID lights, 5 hyd, high flow hyds w/ pwr beyond, 3 PTO’s, 380/90R54 rear duals, 380/8038 front duals, 2490 hrs
 
2015 New Holland T8.350 MFWD, 18 spd power shift, deluxe cab, guidance ready- no GPS or steering technology included, front HID lights, 5 hyd, high flow hyds w/ pwr beyond, 3 PTO’s, 380/90R54 rear duals, 380/80R38 front duals, only 491 hrs, SN#ZFRE02126
 
2010 Challenger MT565B MFWD, CAH, power shift, 3pt, PTO, 3 hyd, SN#V151065
 
1996 Case IH 9370 4WD, power shift, 4 hyd, 20.8-42 duals- good rubber, SN#JEE0036234
 
2000 New Holland TM135 MFWD, power shift, left hand reverse, 3pt, 540/1000 PTO, 3 hyd, 18.4-42 rears, 480/85R28 fronts, Quicke Q980 QA loader w/ bucket & 4 tine grapple, Euro QA bucket, factory joystick, SN#147374B
 
Pair of 380/90R54 tires, 10 bolt rims & spacers for NH rear tractor triples
 
 
COMBINES & HEADS:
 
2008 New Holland CR9080 combine, deluxe cab, dual spd rotor, lateral tilt feeder, yield & moisture monitor, remote adj sieves, straw chopper, small grain concaves, SN#HAJ111037
 
2008 New Holland CR9070 combine, deluxe cab, auto guidance w/ 252 receiver, dual spd rotor, variable spd feeder, lateral tilt feeder, yield & moisture monitor, remote adj sieves, straw chopper, small grain concaves, 520/85R42 duals, SN#HAJ111527
 
2014 New Holland 880CF-40 40' Superflex flex draper head, finger reel, F/A, 3” cut, center double knife drive, gauge wheels, single pt hookup, low acres, SN#YEH042136
 
2013 Case IH 2162 40' flex draper head, 2000 series AWS air bar, pea auger, finger reel, F/A, 3” cut, slow spd transport, CIH flagship/ NH CR adaptor, SN#YDZN34940
 
2013 Case IH 2162 40' flex draper head, finger reel, F/A, 3” cut, double knife drive, slow spd transport, CIH flagship/NH CR adaptor, SN#YDZN35172
 
SPRAYERS, FLOATERS & CHEMICAL EQUIPMENT:
 
2011 New Holland 365F self-propelled sprayer, 120' front booms, 1600 gal stainless steel tank, rear wheel nozzles, 10 section, fence row nozzles, high-capacity 300 gal pump, Raven Viper Pro controller, Ultraglide height control, Capstan Sharp Shooter, Raven auto steer, 380/90R50 tires, SN#YBYM00229
 
Ag Chem 8103 Terragator dry fert floater, JD diesel eng, Terra Shift trans, 70 ft air booms, elec roll tarp, air ride cab, Raven Stark Link Smartrax GPS, Falcon 2 rate controller, 66x43-25 tires, 5221 hrs-recently replaced tires, recently replaced fans, coolers, top distributor, augers, new bottom auger, 1 year on new hyd pump
 
Ag Chem 8103 Terragator dry fert floater, JD diesel eng, Terra shift trans, 70' air booms, elec roll tarp, air ride cab, Raven SCS5000 rate controller, Outback auto steer, 66x43-25 tires, 5534 hrs-3 year-old booms, 1 year on new rear wheel seals, new blower fan housing
 
Ag Chem Rogator 854 self-propelled sprayer, Raven monitor, Trimble EZ-Steer w/ Case IH display & receiver, poly tank, on board mix cone, 230/95R48 tires, 12 bolt hubs for rear duals, SN#8531248
 
AG Chem Rogator SS 1074, 100' booms, 1000 gal stainless steel tank, adj axles, 5 section shut off, Viper Pro controller, 3" fill, Raven auto guidance, 3446 hrs; nozzle bodies removed & hydro needs work
 
Summers 90’ susp boom pull type sprayer, 1500 gal tank, triple nozzle bodies, 3 section boom control, 440 Raven controller, SN#B0763
 
Unused Enduraplas 1100 gal nurse trailer, tandem axle factory chassis w/ full drain white poly tank, unused 2” Honda pump, discharge hose & lights
 
Unused Enduraplas 1100 gal nurse trailer, tandem axle factory chassis w/ full drain white poly tank, unused 2” Honda pump, discharge hose & lights
 
Harriston 24R22 band sprayer – 300 gallon tank, guide cones, gauge wheels, pto Hypro roller pump, controller and extra parts
 
Brittonya 24R22 band/broadcast sprayer – 500 gallon tank, hydraulic Hypro roller pump, extra carts and parts
 
AIR SEEDERS & PLANTERS:
 
2011 New Holland P2070 60' precision hoe drill, 10” spacing, blockage monitors on manifolds, double shoot 4.5” rubber press wheels, New Holland P1060 3 compartment 430bu tow behind cart, variable rate control, less than 1000 acres, excellent condition
 
2001 JD 1820 60' air hoe drill, 7.5” spacing, closing disks on 2 rear rows, rubber press wheels, full run blockage monitor, 5 sec fold, castering front gauge wheels, 1900 3 compartment 430 bu cart w/ fill auger, Titan 710/70R38 tires, SN#A01820X690238
 
2014 Great Plains YP2425A 60' twin row planter, true count clutches, row pro, unit mounted coulters, row cleaners, 500 gal fert tank, SN#GPB1060
 
2004 Kinze 24R22 Twinline planter, finger pkp units, 1.6 bu boxes, ground drive, row cleaners, turn table transport, wing gauge wheels, markers, SN#31281
 
2001 JD 1770 16R30 front fold planter, 2 pt hitch, 3bu boxes, liquid fert w/ factory tanks & pump, row cleaners, markers, brown box control, SN#H01770A670455
 
TILLAGE EQUIPMENT:
 
2014 Horsch RT400 40’ Joker high speed disk, 3 sec fold, blades measure 24”, hyd tongue adj, manual single pt depth control, rear packer, 445/65R22.5 heavy duty Firestone carrier tires, very low acres, SN#310040014001
 
2014 Case IH 330 True Tandem 33’ Turbo Till vertical tillage tool w/ 3 section fold, wing gauge wheels & rolling baskets, cushion gang, 8” spacing, 18” wave coulters & leveling hitch, SN#YDD008647
 
2010 Bourgault 8810 40' field cultivator, 3 section fold, 9" spacing, rear hitch, 4 bar factory harrow, floating tongue, castering gauge wheels, knock on sweeps, SN#B123451
 
2005 Summers 38' Diamond disk, 3 section fold, SN#E0006
 
2007 Summers 40’ Super Coulter Plus, 13 wave coulters on front gang, 17 ½” diameter; 13 wave coulters on rear gang, 19 ½” diameter; no harrow or baskets, SN#G0395
 
 
 
 
GRAIN HANDLING EQUIPMENT:
 
2014 Brandt 1545 Grain Belt 45’ conveyor w/ field loader hopper, self-contained hyd self propelled mover, Kohler Command Pro 30hp gas eng, SN#108596-14
 
2010 Batco 1340TD 13"X40' enclosed belt conveyor, top drive, elec motor, standard hopper, SN#130178
 
Westfield MK130-61 13"X61' auger w/ swing hopper, 540 pto, SN#123522
 
Farmking 1370 13"X70' auger w/ swing hopper, SN#9190473
 
 
MOWER/ CONDITIONER:
 
2014 New Holland H7460 16' discbine mower conditioner, swing tongue, standard drawbar, 1000 pto, rubber on rubber chevron rollers, SN#YDN098341
 
TRAILERS, TRUCK, & PICKUP:
 
1999 Wabash 53’ van trailer, air ride, cargo doors, battery powered lift gate, slider axle, aluminum roof, 101” wide, 295/75R22.5 tires, VIN#1JJV532WXXL582036
 
Fruehauf 5000 gal water trailer, 31' long, rear spray deck, 3" Honda pump & hose, 55 gal mix cone, under body storage boxes, vin#2562- trailer has bonded title can only be transfered to MN buyer, bond expires 06/05/23
 
1980 International S-Series tandem twin screw, 6V92 Detroit engine, flat bed w/ 2200 gal Enduraplas tank, mix cone & pump
 
2011 Chev Silverado LT crew cab 4x4 pkp, air/tilt/cruise, auto start, pwr locks, windows & seat, spray-in box liner, running boards, tonneau cover, box rails, 265/65R18 tires, 178341 miles
 
 
TECHNOLOGY, TOOLS  & OTHER EQUIPMENT:
 
JD Starfire 3000 receiver w/ SF1 activation, SN#PCGT3TB748954
 
Outback CDA-3 receiver & display w/ harness, hoses & steering valve for 9000 series JD tractors
 
Frontier 96" LR5096 landscape rake, 360 degree rotation, 1" tine spacing, cat 1 & quick hitch compatible, used only twice-like new condition
 
Johnson 8’ pull behind snow blower – 540 PTO, poly lined
 
Unused walkthrough skid steer pallet forks w/ HD industrial strength tines
 
Miller Millermatic 250 wire feed welder w/ leads, regulator & assorted tips
 
Miller Millermatic 211 wire feed welder w/ 10' mdx 100 mig gun & 10' work cable & clamps, regulator & gauge w/ hose, power cord, adaptor plugs for 120v & 240v, very little use
 
Honda EU2200i generator, eco throttle, low oil shutdown, parallel operation outlets, 120v 20 amp outlet & 120v 30amp outlet-gen has never been used-like new condition
 
2) Used 30" quad track belts
 
Unused muffler for 1030 Case tractor
 
Pallet of 4 hyd cylinders w/ hose
 
Hd shop built 54”x33” table w/ large caster wheels & lower shelf
 
52’ 220v elec cord
 
Other miscellaneous
 
ALFALFA HAY:
24) 3rd cutting Alfalfa bales 
24) 3rd cutting Alfalfa bales 
11) 3rd cutting Alfalfa bales 
 
 
FEBRUARY ONLINE AUCTION- BIDDING CATALOG NOW POSTED!!
 
Call 701-757-4015 for more details
 
TERMS: Cash, cashier’s check, wire transfer, approved check in US funds.  All sales final.  Statements made auction day take precedence over all advertising.  Document fee on vehicle titles will apply & vehicle titles will be mailed to buyers. 
 
Canadian buyers are always welcome.  Please furnish a letter of credit for registration. Some purchases require payment by wire. Most units move easily across the border, feel free to ask in advance for document assistance if necessary. 
 
AUCTIONEERS & CLERK: Resource Auctions, Dennis Biliske- Auctioneer, 2702 17th Ave S, Grand Forks, ND 58201, ph 701-757-4015, fax 701-757-4016, email- [email protected], website- www.resourceauction.com

Map

Close

Location has been calculated by address and may not be 100% accurate.

Auction Items For Sale

FEBRUARY ONLINE AUCTION
 
BIDS OPEN FEBRUARY 22nd; CLOSE FEBRUARY 26th
 
CLICK HERE FOR ONLINE CATALOG AND BIDDING
 
CLICK ABOVE FOR ONLINE CATALOG INCLUDING EQUIPMENT DESCRIPTIONS, SALE ORDER, BIDDING PROCEDURE, INSPECTION & LOAD OUT LOCATIONS AND ADDITIONAL PHOTOS
 
LOW RATE FINANCING IS AVAILABLE ON MAJOR UNITS, INTEREST WAIVER ON COMBINES. CONTACT MARK AT 701-757-4015 FOR DETAILS…..MUST BE PRE-APPROVED BY FEBRUARY 24th. 
 
TRACTORS:
 
2015 New Holland T8.350 MFWD, Auto Command trans, luxury cab, guidance ready w/ Trimble 1000 display, RTK capable, receiver & Nav II controller, front HID lights, 5 hyd, high flow hyds w/ pwr beyond, 3 PTO’s, 380/90R54 rear duals, 380/8038 front duals, 2490 hrs
 
2015 New Holland T8.350 MFWD, 18 spd power shift, deluxe cab, guidance ready- no GPS or steering technology included, front HID lights, 5 hyd, high flow hyds w/ pwr beyond, 3 PTO’s, 380/90R54 rear duals, 380/80R38 front duals, only 491 hrs, SN#ZFRE02126
 
2010 Challenger MT565B MFWD, CAH, power shift, 3pt, PTO, 3 hyd, SN#V151065
 
1996 Case IH 9370 4WD, power shift, 4 hyd, 20.8-42 duals- good rubber, SN#JEE0036234
 
2000 New Holland TM135 MFWD, power shift, left hand reverse, 3pt, 540/1000 PTO, 3 hyd, 18.4-42 rears, 480/85R28 fronts, Quicke Q980 QA loader w/ bucket & 4 tine grapple, Euro QA bucket, factory joystick, SN#147374B
 
Pair of 380/90R54 tires, 10 bolt rims & spacers for NH rear tractor triples
 
 
COMBINES & HEADS:
 
2008 New Holland CR9080 combine, deluxe cab, dual spd rotor, lateral tilt feeder, yield & moisture monitor, remote adj sieves, straw chopper, small grain concaves, SN#HAJ111037
 
2008 New Holland CR9070 combine, deluxe cab, auto guidance w/ 252 receiver, dual spd rotor, variable spd feeder, lateral tilt feeder, yield & moisture monitor, remote adj sieves, straw chopper, small grain concaves, 520/85R42 duals, SN#HAJ111527
 
2014 New Holland 880CF-40 40' Superflex flex draper head, finger reel, F/A, 3” cut, center double knife drive, gauge wheels, single pt hookup, low acres, SN#YEH042136
 
2013 Case IH 2162 40' flex draper head, 2000 series AWS air bar, pea auger, finger reel, F/A, 3” cut, slow spd transport, CIH flagship/ NH CR adaptor, SN#YDZN34940
 
2013 Case IH 2162 40' flex draper head, finger reel, F/A, 3” cut, double knife drive, slow spd transport, CIH flagship/NH CR adaptor, SN#YDZN35172
 
SPRAYERS, FLOATERS & CHEMICAL EQUIPMENT:
 
2011 New Holland 365F self-propelled sprayer, 120' front booms, 1600 gal stainless steel tank, rear wheel nozzles, 10 section, fence row nozzles, high-capacity 300 gal pump, Raven Viper Pro controller, Ultraglide height control, Capstan Sharp Shooter, Raven auto steer, 380/90R50 tires, SN#YBYM00229
 
Ag Chem 8103 Terragator dry fert floater, JD diesel eng, Terra Shift trans, 70 ft air booms, elec roll tarp, air ride cab, Raven Stark Link Smartrax GPS, Falcon 2 rate controller, 66x43-25 tires, 5221 hrs-recently replaced tires, recently replaced fans, coolers, top distributor, augers, new bottom auger, 1 year on new hyd pump
 
Ag Chem 8103 Terragator dry fert floater, JD diesel eng, Terra shift trans, 70' air booms, elec roll tarp, air ride cab, Raven SCS5000 rate controller, Outback auto steer, 66x43-25 tires, 5534 hrs-3 year-old booms, 1 year on new rear wheel seals, new blower fan housing
 
Ag Chem Rogator 854 self-propelled sprayer, Raven monitor, Trimble EZ-Steer w/ Case IH display & receiver, poly tank, on board mix cone, 230/95R48 tires, 12 bolt hubs for rear duals, SN#8531248
 
AG Chem Rogator SS 1074, 100' booms, 1000 gal stainless steel tank, adj axles, 5 section shut off, Viper Pro controller, 3" fill, Raven auto guidance, 3446 hrs; nozzle bodies removed & hydro needs work
 
Summers 90’ susp boom pull type sprayer, 1500 gal tank, triple nozzle bodies, 3 section boom control, 440 Raven controller, SN#B0763
 
Unused Enduraplas 1100 gal nurse trailer, tandem axle factory chassis w/ full drain white poly tank, unused 2” Honda pump, discharge hose & lights
 
Unused Enduraplas 1100 gal nurse trailer, tandem axle factory chassis w/ full drain white poly tank, unused 2” Honda pump, discharge hose & lights
 
Harriston 24R22 band sprayer – 300 gallon tank, guide cones, gauge wheels, pto Hypro roller pump, controller and extra parts
 
Brittonya 24R22 band/broadcast sprayer – 500 gallon tank, hydraulic Hypro roller pump, extra carts and parts
 
AIR SEEDERS & PLANTERS:
 
2011 New Holland P2070 60' precision hoe drill, 10” spacing, blockage monitors on manifolds, double shoot 4.5” rubber press wheels, New Holland P1060 3 compartment 430bu tow behind cart, variable rate control, less than 1000 acres, excellent condition
 
2001 JD 1820 60' air hoe drill, 7.5” spacing, closing disks on 2 rear rows, rubber press wheels, full run blockage monitor, 5 sec fold, castering front gauge wheels, 1900 3 compartment 430 bu cart w/ fill auger, Titan 710/70R38 tires, SN#A01820X690238
 
2014 Great Plains YP2425A 60' twin row planter, true count clutches, row pro, unit mounted coulters, row cleaners, 500 gal fert tank, SN#GPB1060
 
2004 Kinze 24R22 Twinline planter, finger pkp units, 1.6 bu boxes, ground drive, row cleaners, turn table transport, wing gauge wheels, markers, SN#31281
 
2001 JD 1770 16R30 front fold planter, 2 pt hitch, 3bu boxes, liquid fert w/ factory tanks & pump, row cleaners, markers, brown box control, SN#H01770A670455
 
TILLAGE EQUIPMENT:
 
2014 Horsch RT400 40’ Joker high speed disk, 3 sec fold, blades measure 24”, hyd tongue adj, manual single pt depth control, rear packer, 445/65R22.5 heavy duty Firestone carrier tires, very low acres, SN#310040014001
 
2014 Case IH 330 True Tandem 33’ Turbo Till vertical tillage tool w/ 3 section fold, wing gauge wheels & rolling baskets, cushion gang, 8” spacing, 18” wave coulters & leveling hitch, SN#YDD008647
 
2010 Bourgault 8810 40' field cultivator, 3 section fold, 9" spacing, rear hitch, 4 bar factory harrow, floating tongue, castering gauge wheels, knock on sweeps, SN#B123451
 
2005 Summers 38' Diamond disk, 3 section fold, SN#E0006
 
2007 Summers 40’ Super Coulter Plus, 13 wave coulters on front gang, 17 ½” diameter; 13 wave coulters on rear gang, 19 ½” diameter; no harrow or baskets, SN#G0395
 
 
 
 
GRAIN HANDLING EQUIPMENT:
 
2014 Brandt 1545 Grain Belt 45’ conveyor w/ field loader hopper, self-contained hyd self propelled mover, Kohler Command Pro 30hp gas eng, SN#108596-14
 
2010 Batco 1340TD 13"X40' enclosed belt conveyor, top drive, elec motor, standard hopper, SN#130178
 
Westfield MK130-61 13"X61' auger w/ swing hopper, 540 pto, SN#123522
 
Farmking 1370 13"X70' auger w/ swing hopper, SN#9190473
 
 
MOWER/ CONDITIONER:
 
2014 New Holland H7460 16' discbine mower conditioner, swing tongue, standard drawbar, 1000 pto, rubber on rubber chevron rollers, SN#YDN098341
 
TRAILERS, TRUCK, & PICKUP:
 
1999 Wabash 53’ van trailer, air ride, cargo doors, battery powered lift gate, slider axle, aluminum roof, 101” wide, 295/75R22.5 tires, VIN#1JJV532WXXL582036
 
Fruehauf 5000 gal water trailer, 31' long, rear spray deck, 3" Honda pump & hose, 55 gal mix cone, under body storage boxes, vin#2562- trailer has bonded title can only be transfered to MN buyer, bond expires 06/05/23
 
1980 International S-Series tandem twin screw, 6V92 Detroit engine, flat bed w/ 2200 gal Enduraplas tank, mix cone & pump
 
2011 Chev Silverado LT crew cab 4x4 pkp, air/tilt/cruise, auto start, pwr locks, windows & seat, spray-in box liner, running boards, tonneau cover, box rails, 265/65R18 tires, 178341 miles
 
 
TECHNOLOGY, TOOLS  & OTHER EQUIPMENT:
 
JD Starfire 3000 receiver w/ SF1 activation, SN#PCGT3TB748954
 
Outback CDA-3 receiver & display w/ harness, hoses & steering valve for 9000 series JD tractors
 
Frontier 96" LR5096 landscape rake, 360 degree rotation, 1" tine spacing, cat 1 & quick hitch compatible, used only twice-like new condition
 
Johnson 8’ pull behind snow blower – 540 PTO, poly lined
 
Unused walkthrough skid steer pallet forks w/ HD industrial strength tines
 
Miller Millermatic 250 wire feed welder w/ leads, regulator & assorted tips
 
Miller Millermatic 211 wire feed welder w/ 10' mdx 100 mig gun & 10' work cable & clamps, regulator & gauge w/ hose, power cord, adaptor plugs for 120v & 240v, very little use
 
Honda EU2200i generator, eco throttle, low oil shutdown, parallel operation outlets, 120v 20 amp outlet & 120v 30amp outlet-gen has never been used-like new condition
 
2) Used 30" quad track belts
 
Unused muffler for 1030 Case tractor
 
Pallet of 4 hyd cylinders w/ hose
 
Hd shop built 54”x33” table w/ large caster wheels & lower shelf
 
52’ 220v elec cord
 
Other miscellaneous
 
ALFALFA HAY:
24) 3rd cutting Alfalfa bales 
24) 3rd cutting Alfalfa bales 
11) 3rd cutting Alfalfa bales 
 
 
FEBRUARY ONLINE AUCTION- BIDDING CATALOG NOW POSTED!!
 
Call 701-757-4015 for more details
 
TERMS: Cash, cashier’s check, wire transfer, approved check in US funds.  All sales final.  Statements made auction day take precedence over all advertising.  Document fee on vehicle titles will apply & vehicle titles will be mailed to buyers. 
 
Canadian buyers are always welcome.  Please furnish a letter of credit for registration. Some purchases require payment by wire. Most units move easily across the border, feel free to ask in advance for document assistance if necessary. 
 
AUCTIONEERS & CLERK: Resource Auctions, Dennis Biliske- Auctioneer, 2702 17th Ave S, Grand Forks, ND 58201, ph 701-757-4015, fax 701-757-4016, email- [email protected], website- www.resourceauction.com
Contact chat